Digi TransPort LR54-AA401 User Manual Download Page 136

Page: 136 / 169

Command descriptions

TransPort LR User Guide

183

mtu

Maximum Transmission Unit (MTU) for the DSL interface.

remote-vendor-id

The remote vendor ID of the DSLAM to which the DSL interface is connected.

ip-address

IP address of the DSL interface.

mask

Address mask of the DSL interface.

gateway

Gateway address of the DSL interface.

rx-packets

Number of packets received by the DSL interface.

tx-packets

Number of packets transmitted by the DSL interface.

rx-bytes

Number of bytes received by the DSL interface.

tx-bytes

Number of bytes transmitted by the DSL interface.

downstream-speed

Current speed of the downstream DSL channel, in kbps.

upstream-speed

Current speed of the upstream DSL channel, in kbps.

downstream-channel-type

The channel type being used on the downstream DSL channel, either Fast or Interleaved.

upstream-channel-type

The channel type being used on the upstream DSL channel, either Fast or Interleaved.

downstream-relative-capacity

The current relative capacity on the downstream DSL channel. The relative capacity is the
percentage of overall available bandwidth.

Summary of Contents for TransPort LR54-AA401










































































































































































Search results

Summary of Contents for TransPort LR54-AA401

Reviews:

Related manuals for TransPort LR54-AA401

Brands by name

Popular brands

Digi TransPort LR54-AA401, User Manual

Search results

Summary of Contents for TransPort LR54-AA401

Reviews:

Related manuals for TransPort LR54-AA401

Brands by name

Popular brands