background image

www.desatech.com

121486-01F

16

PRESSURE TESTING HEATER GAS 

CONNECTIONS

1.  Open equipment shutoff valve (see Figure 

18, page 15).

2.  Open main gas valve located on or near 

gas meter for natural gas or open propane/
LP supply tank valve.

3.  Make sure control knob of heater is in the 

OFF position.

4.  Check all joints to gas control (see Figures 

19  or  20,  page  15). Apply  noncorrosive 
leak detection fluid to all joints. Bubbles 
forming show a leak.

5.  Correct all leaks at once.
6.  Light  heater  (see 

Operation

,  page  17). 

Check all other internal joints for leaks.

7.  Turn  off  heater  (see 

To  Turn  Off  Gas  to 

Appliance

, page 19).

INSTALLING LOGS

 WARNING: Failure to posi

-

tion  the  parts  in  accordance 

with  these  diagrams  or  failure 

to  use  only  parts  specifically 

approved with this heater may 

result  in  property  damage  or 

personal injury.

  CAUTION:  After  installa-

tion and periodically thereafter, 

check  to  ensure  that  no  flame 

comes in contact with any log. 

With the heater set to HI, check 

to see if flames contact any log. If 

so, reposition logs according to 

the log installation instructions 

in this manual. Flames contact

-

ing logs will create soot.

It is very important to install the logs exactly 
as instructed. Do not modify logs. Only use 
logs supplied with heater.
1.  Place rear log (log #1) behind burner on the 

two pins on rear bracket (see Figure 21).

2.  Place  cutouts  of  middle  log  (log  #2)  on 

burner as shown in Figure 22.

3.  Place left front log (log #3) on grate prongs 

as shown in Figure 23.

Figure 21 - Rear Log (Log #1) Placement

Figure 22 - Middle Log (Log #2) 

Placement

Log #1

Log #2

Cutout

Cutout

Figure 23 - Placement of Front Logs  

(Log #3 and Log #4)

Log #4

Grate 
Prongs

Log #3

Peg

INSTALLATION

Continued 

Summary of Contents for LDL3930NRB

































Reviews: