background image

www.desatech.com

121486-01F

10

INSTALLATION

Continued 

Figure 5 - Heat Resistant Material (Slate, 

Marble, Tile, etc.) Above Fireplace

Noncombustible 

Material 

Distance (A)

Requirements for 

Safe Installation

12" or more

Noncombustible 
material OK.

Between 8" and 
12"

Install fireplace hood 
accessory (GA6050, 
GA6052, or GA6053 see 

Accessories

, page 29).

Less than 8"

Noncombustible mate-
rial must be extended 
to at least 8". See 
Between 8" and 12", 
above. If you cannot 
extend material, you 
must operate heater 
with flue damper open.

If Using Mantel

You  must  have  noncombustible  material(s) 
above the fireplace opening. Noncombustible 
materials (such as slate, marble, tile, etc.) must 
be at least 1/2" thick. With sheet metal, you 
must have noncombustible material behind it. 
Noncombustible material must extend at least 
8" up. If noncombustible material is less than 
12", you must install the fireplace hood acces-
sory. Even if noncombustible material is more 
than 12", you may need the hood accessory to 
deflect heat away from your mantel shelf. See 
Figures 5, 6 and 7 for minimum clearances. 

IMPORTANT:

 If you cannot meet these mini-

mum  clearances,  you  must  operate  heater 
with chimney flue damper open. Go to 

Install-

ing  Damper  Clamp  Accessory  for  Vented 
Operation

, page 11.

MANTEL CLEARANCES

In addition to meeting noncombustible mate-
rial clearances, you must also meet required 
clearances  between  fireplace  opening  and 
mantel shelf. If you do not meet the clearances 
listed below, you will need a hood.

Determining Minimum Mantel Clearance

If  you  meet  minimum  clearance  between 
mantel shelf and top of fireplace opening, a 
hood is not required (see Figure 6).

Determining Minimum Mantel Clearance 
When Using a Hood

If minimum clearances in Figure 6 are not met, 
you must have a hood. When using a hood 
there are still certain minimum mantel clear-
ances required. Follow minimum clearances 
shown in Figure 7 when using hood.

Figure 6 - Minimum Mantel Clearances 

Without Using Hood

Figure 7 - Minimum Mantel Clearances 

When Using Hood

Minimum

Noncombustible 

Material 

Minimum

Noncombustible 

Material Height 

Distances to 

Underside of

Mantel 

Top of

Fireplace

Opening

Underside

of Mantel

Shelf

Mantel Shelf

12"

(

A

18" 20"

22"

24"

All

minimum 

distances

are in

inches

1

/

2

"

6"

8"

10"

Minimum
Noncombustible 
Material 

8"
Min.

12" 15" 18" 20"

2½"

6"

8"

10"

12"

Distances to 
Underside of
Mantel 

Hood
(GA6050,
GA6052 or
GA6053)

Top of
Fireplace
Opening

Underside
of Mantel
Shelf

Mantel Shelf

Summary of Contents for LDL3930NRB

































Reviews: