background image

www.desatech.com

121486-01F

15

INSTALLATION

Continued 

CHECKING GAS CONNECTIONS

 WARNING: Test all gas pip

-

ing  and  connections,  internal 

and  external  to  unit,  for  leaks 

after installing or servicing. Cor

-

rect all leaks at once.

  WARNING:  Never  use  an 

open flame to check for a leak. 

Apply  a  noncorrosive  leak 

detection  fluid  to  all  joints. 

Bubbles forming show a leak. 

Correct all leaks at once.

 CAUTION: Make sure exter-

nal regulator has been installed 

between  propane/LP  supply 

and heater. See guidelines un

-

der 

Connecting to Gas Supply

page 13.

PRESSURE TESTING GAS SUPPLY 
PIPING SYSTEM 
Test Pressures In Excess Of 1/2 PSIG 
(3.5 kPa)

1.  Disconnect  appliance  with  its  appliance 

main gas valve (control valve) and equip-
ment shutoff valve from gas supply piping 
system. Pressures in excess of 1/2 psig 
will damage heater regulator.

2.  Cap off open end of gas pipe where equip-

ment shutoff valve was connected.

3.  Pressurize supply piping system by either 

opening propane/LP supply tank valve for 
propane/LP gas or opening main gas valve 
located on or near gas meter for natural 
gas, or using compressed air.

4.  Check all joints of gas supply piping system. 

Apply noncorrosive leak detection fluid to 
all joints. Bubbles forming show a leak.

5.  Correct all leaks at once.
6.  Reconnect heater and equipment shutoff 

valve to gas supply. Check reconnected 
fittings for leaks. 

Test Pressures Equal To or Less Than 
1/2 PSIG (3.5 kPa)

1.  Close equipment shutoff valve (see Fig-

ure 18).

2.  Pressurize supply piping system by either 

opening propane/LP supply tank valve for 
propane/LP gas or opening main gas valve 
located on or near gas meter for natural 
gas, or using compressed air.

3.  Check all joints from gas meter to equip-

ment shutoff valve for natural gas or pro-
pane/LP supply to equipment shutoff valve 
for propane/LP (see Figures 19 and 20). 
Apply noncorrosive leak detection fluid to 
all joints. Bubbles forming show a leak. 

4.  Correct all leaks at once.

Open

Closed

Gas Meter

Equipment 

Shutoff 

Valve

Gas Control 

Valve Location

Figure 20 - Checking Gas Joints (Natural 

Gas only)

Figure 18 - Equipment Shutoff Valve

Figure 19 - Checking Gas Joints 

(Propane/LP only)

Gas Control 
Valve Location

Propane/LP 
Supply Tank

Equipment 
Shutoff Valve

Equipment 
Shutoff Valve

Summary of Contents for LDL3930NRB

































Reviews: