background image

www.desatech.com

121486-01F

27

TROUBLESHOOTING

Continued

 WARNING: If you smell gas

•  Shut off gas supply.

•  Do not try to light any appliance.

•  Do not touch any electrical switch; do not use any phone in your 

building.

•  Immediately call your gas supplier from a neighbor’s phone. Fol

-

low the gas supplier’s instructions.

•  If you cannot reach your gas supplier, call the fire department.

IMPORTANT:

 Operating heater where impurities in air exist may create odors. Cleaning sup-

plies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles, etc., 
create fumes. These fumes may mix with combustion air and create odors. These odors will 
disappear over time.

POSSIBLE CAUSE

1. Metal  expanding  while 

heating  or  contracting 
while cooling

1. Heater  burning  vapors 

from  paint,  hair  spray, 
glues,  cleaners,  chemi-
cals, new carpet, etc. (See

 

IMPORTANT

  statement 

above)

2. Low fuel supply (propane/

LP only)

3. Gas  leak.

  See  Warn-

ing  statement  at  top  of 
page

1. Not  enough  fresh  air  is 

available

2. Low line pressure

3. ODS/pilot  is  partially 

clogged

1. Gas  leak. 

See  Warn-

ing  statement  at  top  of 
page

2. Control valve defective

1. Foreign  matter  between 

control valve and burner

2. Gas  leak. 

See  Warn-

ing  statement  at  top  of 
page

REMEDY

1. This  is  normal  with  most 

heaters.  If  noise  is  ex-
cessive,  contact  qualified 
service person

1. Open window to ventilate 

room.  Stop  using  odor 
causing  products  while 
heater is running

2. Refill  supply  tank  (pro-

pane/LP only)

3. Locate  and  correct  all 

leaks  (see 

Checking  Gas 

Connections

, page 15)

1. Open window and/or door 

for ventilation

2. Contact  local  natural  or 

propane/LP gas company

3. Clean  ODS/pilot  (see 

Cleaning  and  Mainte-
nance

, page 22)

1. Locate  and  correct  all 

leaks  (see 

Checking  Gas 

Connections

, page 15)

2. Replace control valve

1. Take apart gas tubing and 

remove foreign matter

2. Locate  and  correct  all 

leaks  (see 

Checking  Gas 

Connections

, page 15)

OBSERVED PROBLEM

Heater  produces  a  clicking/
ticking noise just after burners 
are lit or shut off

Heater  produces  unwanted 
odors

Heater shuts off in use (ODS 
operates)

Gas odor even when control 
knob is in OFF position

Gas odor during combustion

Summary of Contents for LDL3930NRB

































Reviews: