Vermont Castings Radiance RADVTBB Скачать руководство пользователя

Страница: 1 / 52

INSTALLER / CONSUMER

SAFETY INFORMATION

20012697 1/08 Rev. 3

PLEASE READ THIS MANUAL
BEFORE INSTALLING AND USING
APPLIANCE.

WARNING!

IF THE INFORMATION IN THIS
MANUAL IS NOT FOLLOWED
EXACTLY, A FIRE OR EXPLOSION
MAY RESULT CAUSING
PROPERTY DAMAGE, PERSONAL
INJURY OR LOSS OF LIFE.

FOR YOUR SAFETY

Installation and service must be
performed by a qualiﬁed installer,
service agency or the gas suppler.

WHAT TO DO IF

YOU SMELL GAS:

•

Do not try to light any appliance.

•

Do not touch any electric switch; do
not use any phone in your building.

•

Immediately call your gas supplier
from your neighbor’s phone. Follow
the gas supplier’s instructions.

•

If you cannot reach your gas supplier,
call the ﬁre department.

DO NOT STORE OR USE
GASOLINE OR OTHER
FLAMMABLE VAPORS AND
LIQUIDS IN THE VICINITY OF THIS
OR ANY OTHER APPLIANCE.

This appliance may be installed in an
after market permanently located
manufactured (mobile) home where not
prohibited by local codes.

This appliance is only for use with the
type of gas indicated on the rating plate.

This appliance is not convertible for use
with other gases unless a certiﬁed kit is
used.

Radiance
Direct Vent Gas Heater

Models:

RADVT Series: RADVTCB, RADVTEB, RADVTMB,
RADVTBS, RADVTCH, RADVTVG, RADVTBD, RAD-
VTBB, RADVTCG, RADVTGG, RADVTSG,
RADVTC Series: RADVTCCB, RADVTCEB,
RADVTCMB, RADVTCBS, RADVTCCH, RADVTCVG,
RADVTCBD, RADVTCBB, RADVTCCG, RADVTCSG

Homeowner’s Installation

and Operating Manual

CERTIFIED

DESIGN

CERTIFIED

12697

Radiance cover

7/07

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

Содержание Radiance RADVTBB





















































Результаты поиска

Содержание Radiance RADVTBB

Отзывы:

Похожие инструкции для Radiance RADVTBB

Бренды по названию

Популярные бренды

Vermont Castings Radiance RADVTBB, Руководство по установке и эксплуатации для владельцев жилья

Результаты поиска

Содержание Radiance RADVTBB

Отзывы:

Похожие инструкции для Radiance RADVTBB

Бренды по названию

Популярные бренды