background image

www.desatech.com

121486-01F

14

We  recommend  that  you  install  a  sediment 
trap  in  supply  line  as  shown  in  Figure  17. 
Locate sediment trap where it is within reach 
for cleaning. Install in piping system between 
fuel  supply  and  heater.  Locate  sediment 
trap  where  trapped  matter  is  not  likely  to 
freeze. A  sediment  trap  traps  moisture  and 
contaminants.  This  keeps  them  from  going 
into  heater  controls.  If  sediment  trap  is  not 
installed  or  is  installed  wrong,  heater  may 
not run properly.

 CAUTION: Avoid damage to 

gas control. Hold gas fitting with 

wrench  when  connecting  it  to 

gas piping and/or fittings.

INSTALLATION

Continued 

  CAUTION:  Use  only  new, 

black  iron  or  steel  pipe.  Inter

-

nally-tinned copper tubing may 

be used in certain areas. Check 

your  local  codes.  Use  pipe  of 

1/2" diameter or greater to allow 

proper gas volume to heater. If 

pipe is too small, undue loss of 

volume will occur.

Installation must include an equipment shutoff 
valve, union, and plugged 1/8" NPT tap. Lo-
cate NPT tap within reach for test gauge hook 
up. NPT tap must be upstream from heater 
(see Figure 17).

IMPORTANT:

 Install equipment shutoff valve 

in  an  accessible  location.  The  equipment 
shutoff valve is for turning on or shutting off 
the gas to the appliance.
Check  your  building  codes  for  any  special 
requirements for locating equipment shutoff 
valve to fireplaces.
Apply pipe joint sealant lightly to male NPT 
threads. This will prevent excess sealant from 
going into pipe. Excess sealant in pipe could 
result in clogged heater valves.

  WARNING:  Use  pipe  joint 

sealant that is resistant to liquid 

petroleum (LP) gas. 

Propane/LP 
Supply Tank

External Regulator

Figure 16 - External Regulator With Vent 

Pointing Down

Vent 
Pointing 
Down

Pipe     Cap    Tee 
Nipple   

Joint

* Purchase the optional CSA design-certified 
equipment shutoff valve from your dealer.
** Minimum inlet pressure for purpose of input 
adjustment. 

Figure 17 - Gas Connection

Gas Control 

3" Min.

Sediment Trap

Propane/
LP

- From 

External 
Regulator 
(11" W.C.** 
to 14" W.C. 
Pressure)

Natural

From Gas 
Meter (5" 
W.C.** to 
10.5" W.C. 
Pressure)

CSA Design-
Certified Equipment 
Shutoff Valve With 
1/8" NPT Tap*

Approved Flexible 
Gas Hose (if allowed 
by local codes)

Summary of Contents for LDL3930NRB

































Reviews: