background image

www.desatech.com

121486-01F

9

INSTALLATION

Continued 

Carefully follow the instructions below. This 
will ensure safe installation into a masonry, 
UL127-listed manufactured fireplace, or listed 
vent-free firebox.

Minimum Clearances For Side 

Combustible Material, Side Wall, and 
Ceiling

A.  Clearances from the side of the fireplace 

cabinet to any combustible material and 
wall should follow diagram in Figure 4.

 

Example:

 The face of a mantel, bookshelf, 

etc. is made of combustible material and 
protrudes 3 

1

/

2

" from the wall. This com-

bustible material must be 4" from the side 
of the fireplace cabinet (see Figure 4).

 

Note: When installing your gas logs into 
a  manufactured  firebox,  follow  firebox 
manufacturer’s  instructions  for  minimum 
clearances to combustible materials.

B.  Clearances  from  the  top  of  the  fireplace 

opening to the ceiling should not be less 
than 42". 

Figure 4 - Minimum Clearance for 

Combustible to Wall 

*Minimum 16" from Side Wall 

Example

INSTALLATION AND CLEARANCES 

FOR VENT-FREE OPERATION

  WARNING:  Maintain  the 

minimum  clearances.  If  you 

can, provide greater clearances 

from  floor,  ceiling,  and  adjoin

-

ing wall.

MINIMUM FIREPLACE CLEARANCE TO 

COMBUSTIBLE MATERIALS

 Side Wall 16", Ceiling 42", Front 36"

LOG SIZING REQUIREMENTS

Minimum Firebox

Height Depth

Front 

Width

Rear * 

Width

17"

14"

34"

24"

* Measured at 14" depth.

NOTICE: Manual control heaters 

may be used as a vented product. 

If so, you must always run heater 

with chimney flue damper open. 

If  running  heater  with  damper 

open, noncombustible material 

above fireplace opening is not 

needed. Go to 

Installing Damper 

Clamp  Accessory  for  Vented 

Operation

, page 11.

MINIMUM NONCOMBUSTIBLE 

MATERIAL CLEARANCES

If Not Using Mantel

Note: 

If using  a mantel  proceed  to If Using 

Mantel. If not using a mantel, follow the infor-
mation on this page.
You  must  have  noncombustible  material(s) 
above the fireplace opening. Noncombustible 
materials  (such  as  slate,  marble,  tile,  etc.) 
must be at least 1/2" thick. With sheet metal, 
you must have noncombustible material be-
hind it. Noncombustible material must extend 
at least 8" up. If noncombustible material is 
less than 12", you must install the fireplace 
hood accessory. See Figure 5, page 10 for 
minimum clearances.

*

Summary of Contents for LDL3930NRB

































Reviews: