background image

www.desatech.com

115043-01C

12

CLEANING AND 

MAINTENANCE

•  Keep the area around the log set clean and clear 

of debris.

•  Occasionally, you may use a soft bristle brush 

to clean logs.

•  Once every year a qualified agency or certified 

chimney sweep should examine and clean the 

venting system of the fireplace.

SERVICE HINTS

When Gas Pressure is Too Low

•  pilot will not stay lit
•  burners will have delayed ignition
•  appliance will not produce specified heat
You may feel your gas pressure is too low. If so, 

contact your local  natural gas supplier.

TECHNICAL SERVICE

You may have further questions about installation, 

operation, or troubleshooting. If so, contact DESAʼs 

Technical Service Department at 1-866-672-6040. 

When calling please have your model and serial 

numbers of your appliance ready.
You can also visit DESAʼs technical services web 

site at 

www.desatech.com

.

REPLACEMENT PARTS

Note: 

Use only original replacement parts. This 

will  protect  your  warranty  coverage  for  parts 

replaced under warranty. 

PARTS UNDER WARRANTY

Contact authorized dealers of this product. If they 

canʼt supply original replacement part(s), call DESAʼs 

Technical Service Department at 1-866-672-6040. 

When calling DESA, have ready:
•  your name and address
•  model and serial numbers of your log set 
•  how log set was malfunctioning
•  type of gas used (natural gas)
•  purchase date
Usually, we will ask you to return the part to the 

factory.

PARTS NOT UNDER WARRANTY

Contact authorized dealers of this product. If they 

canʼt  supply  original  replacement  part(s),  call 

DESA at 1-866-672-6040 for referral information. 

When calling DESA, have ready
•  model number of your log set 
•  the replacement part number

Summary of Contents for Comfort Glow BRENTWOOD LCF18





















Reviews: