Delta Tau PMAC2A-PC/104 Installation Manual Download Page 18 | Manualshive

Page: 18 / 72

background image

PMAC2A-PC/104

ACC-2P Hardware Setup

12

The ‘+’ inputs of each differential pair each have a hard-wired 1 k

Ω

pull-up resistor to +5V. This cannot

be changed.
The ‘-‘ inputs of each differential pair each have a hard-wired 2.2 k

Ω

resistor to +5V; each also has

another 2.2 k

Ω

resistor as part of a socketed resistor pack that can be configured as a pull-up resistor to

+5V, or a pull-down resistor to GND.
If this socketed resistor is configured as a pull-down resistor (the default configuration), the combination
of pull-up and pull-down resistors on this line acts as a voltage divider, holding the line at +2.5V in the
absence of an external signal. This configuration is

required

for single-ended inputs using the ‘+’ lines

alone; it is desirable for unconnected inputs to prevent the pick-up of spurious noise; it is permissible for
differential line-driver inputs.
If this socketed resistor is configured as a pull-up resistor (by reversing the SIP pack in the socket), the
two parallel 2.2 k

Ω

resistors act as a single 1.1 k

Ω

pull-up resistor, holding the line at +5V in the absence

of an external signal. This configuration is

required

if complementary open-collector drivers are used; it

is permissible for differential line-driver inputs.
If Pin 1 of the resistor pack, marked by a dot on the pack, matches Pin 1 of the socket, labeled by a white
square, then the pack is configured as a bank of pull-down resistors. If the pack is reversed in the socket,
it is configured as a bank of pull-up resistors.
RP22 is the 6-pin pull-up/pull-down resistor pack for the handwheel encoder input.

Handwheel Encoder Termination Resistors

The PMAC provides a socket for termination resistors on the handwheel encoder differential input pairs
coming into the board. As shipped, there is no resistor pack in the RP23 socket. If these signals are
brought long distances into the PMAC board and ringing at signal transitions is a problem, a SIP resistor
pack may be mounted on the RP23 socket to reduce or eliminate the ringing. The 6-pin termination
resistor pack is the type that has independent resistors (no common connection) with each resistor using 2
adjacent pins.

«
...
16
17
18
19
20
...
»

Summary of Contents for PMAC2A-PC/104









































































Reviews:

No comments

Related manuals for PMAC2A-PC/104

Brand: Farallon Pages: 26

Brand: Observint Pages: 11

Brand: TC Electronic Pages: 55

Brand: IBA Pages: 29

Brand: IBA Pages: 33

Brand: AXAGO Pages: 2

NetVanta Analog Modem Dial Backup Interface Module

Brand: ADTRAN Pages: 2

Brand: Dataprobe Pages: 16

Brand: Paradyne Pages: 108

Brand: IBA Pages: 36

USB device 622x

Brand: National Instruments Pages: 23

Brand: Sony Ericsson Pages: 2

Brand: ADLINK Technology Pages: 69

Brand: ICP DAS USA Pages: 8

RS2BL040 - Raid Controller

Brand: Intel Pages: 5

Database Appliance X6-2-HA

Brand: Oracle Pages: 473

Brand: Motorola Pages: 376

Brand: Motorola Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands