manualshive.com logo in svg

Delta Tau PMAC2A-PC/104, Installation Manual, Page: 25 / 72

Share
Download
Delta Tau PMAC2A-PC/104 Installation Manual Download Page 25

PMAC2A-PC/104

 

 

Machine Connections 

19

 

 
 

Serial Port (JRS232 Port) 

For serial communications, use a serial cable to connect your PC's COM port to the J8 serial port 
connector present on the PMAC2A-PC/104 base board.  Delta Tau provides the Accessory 3L cable for 
this purpose that connects the PMAC to a DB-9 connector.  Standard DB-9-to-DB-25 or DB-25-to-DB-9 
adapters may be needed for your particular setup. If a cable needs to be made, the easiest approach is to 
use a flat cable prepared with flat-cable type connectors as indicated in the following diagram: 
 
 

 
 
 
 
 

ACC-2P Ethernet RJ45 Connector 
(J10 Port) 

This connector is used for Ethernet communications from the ACC-2P to a PC, and it is provided when 
ACC-2P Option 1B is ordered.  The PC must have a card dedicated solely to the PMAC network.  The 
appropriate Category 5 10/100-Base T network cable that mates to this connector can be readily 
purchased from any local computer store.  The type of network cable to purchase depends on the 
configuration to the host PC. 
When making a 

direct

 connection to a Host communication Ethernet card in a PC a “cat 5 networking 

crossover cable” 

must

 be used.  A standard cat 5 straight through networking cable cannot be used in this 

scenario. When using a connection to a network hub or switch, the standard cat 5 straight through 
networking cable must be used, and not a crossover cable. 
Performance can be degraded seriously by the use of a hub or switch. Network hubs or the more 
intelligent network switches have processors inside them, which can add delays of at least 15msec to the 
PMAC communications. 

ACC-2P USB Connector (J1 Port) 

This connector is to be used in conjunction with USB A-B cable, which can be purchased from any local 
computer store, and it is provided when ACC-2P Option 1A is ordered.  The A connector is connected to 
a PC or Hub device; the B connector plugs into the ACC-2P J1 port. 

PMAC (DB-9S) 

PC (DB-9) 

1 (No connect) 

1 (No connect) 

2 (TXD/) 

2 (RXD) 

3 (RXD/) 

3 (TXD) 

4 (DSR) 

4 (DTR) 

5 (Gnd) 

5 (Gnd) 

6 (DTR) 

6 (DSR) 

7 (CTS) 

7 (RTS) 

8 (RTS) 

8 (CTS) 

9 (No connect) 

9 (No connect) 

DB-9

 

Female

 

1

 

1

DB-9

Male

 

Summary of Contents for PMAC2A-PC/104









































































Reviews:

No comments