Delta Tau PMAC2A-PC/104 Installation Manual Download Page 52

Page: 52 / 72

PMAC2A-PC/104

Acc-1P E-Point Jumper Descriptions

ACC-1P E-POINT JUMPER DESCRIPTIONS

E0: Reserved for Future Use

E Point and

Physical Layout

Location Description

Default

For future use.

No jumper

E1 - E2: Machine Output Supply Voltage Configure

E Point and

Physical Layout

Location Description

Default

Jump pin 1 to 2 to apply +V (+5V
to 24V) to pin 10 of "U7" (should
be ULN2803A for sink output
configuration) JOPTO
"MACHINE" outputs M01-M08.

Jump pin 2 to 3 to apply GND to pin
10 of "U7" (should be UDN2981A for
source output configuration).

WARNING;

The jumper setting

must match the type of driver IC, or
damage to the IC will result.

1-2 Jumper

installed

Jump pin 1 to 2 to apply GND to
pin 10 of "U7" (should be
ULN2803A for sink output
configuration).

Jump pin 2 to 3 to apply +V (+5V
to 24V) to pin 10 of "U7" (should
be UDN2981A for source output
configuration).

WARNING;

The jumper setting

must match the type of driver IC, or
damage to the IC will result.

1-2 Jumper

installed

Summary of Contents for PMAC2A-PC/104









































































Search results

Summary of Contents for PMAC2A-PC/104

Reviews:

Related manuals for PMAC2A-PC/104

Brands by name

Popular brands

Delta Tau PMAC2A-PC/104, Installation Manual

Search results

Summary of Contents for PMAC2A-PC/104

Reviews:

Related manuals for PMAC2A-PC/104

Brands by name

Popular brands