Delta Tau PMAC2A-PC/104 Installation Manual Download Page 49

Page: 49 / 72

PMAC2A-PC/104

Base Board E-Point Jumper Descriptions

E13: Power-Up/Reset Load Source

E Point and

Physical Layout

Location Description

Default

E13

Jump pin 1 to 2 to reload firmware
through serial or bus port.

Remove jumper for normal
operation.

No jumper

E14: Watchdog Disable Jumper

E Point and

Physical Layout

Location Description

Default

E14

Jump pin 1 to 2 to disable
WATCHDOG timer (for test
purposes only!!).

Remove jumper to enable
WATCHDOG timer.

No jumper

E15A, B, C: Flash Memory Bank Select

E Point and

Physical Layout

Location Description

Default

E15A

E15C

Remove all 3 jumpers to select
flash memory bank with factory-
installed firmware.

Use other configuration to select
one of the 7 other flash memory
banks

No jumpers

installed

Summary of Contents for PMAC2A-PC/104









































































Search results

Summary of Contents for PMAC2A-PC/104

Reviews:

Related manuals for PMAC2A-PC/104

Brands by name

Popular brands

Delta Tau PMAC2A-PC/104, Installation Manual

Search results

Summary of Contents for PMAC2A-PC/104

Reviews:

Related manuals for PMAC2A-PC/104

Brands by name

Popular brands