Delta Tau PMAC2A-PC/104 Installation Manual Download Page 50

Page: 50 / 72

PMAC2A-PC/104

Base Board E-Point Jumper Descriptions

E16: ADC Inputs Enable

E Point and

Physical Layout

Location Description

Default

E16

Jump pin 1 to 2 to enable the
Option-12 ADC inputs.

Remove jumper to disable the ADC
inputs, which might be necessary
for reading current feedback signals
from digital amplifiers.

No jumper

E18 – E19: PC/104 Bus Address

E Point and

Physical Layout

Location Description

Default

Jumpers E18 and E19 select the
PC/104 bus address for
communications according to the
following table:

E18 E19

Address

(Hex)

Address

(Dec)

OFF OFF $200

512

OFF ON $210

528

ON OFF $220

544

E18

E19

ON ON $230

560

No E18 jumper

installed;

jumper E19

installed

Note

Jumper E18 must be removed and jumper E19 must be installed for using either
the Ethernet or USB optional methods of communication.

Summary of Contents for PMAC2A-PC/104









































































Search results

Summary of Contents for PMAC2A-PC/104

Reviews:

Related manuals for PMAC2A-PC/104

Brands by name

Popular brands

Delta Tau PMAC2A-PC/104, Installation Manual

Search results

Summary of Contents for PMAC2A-PC/104

Reviews:

Related manuals for PMAC2A-PC/104

Brands by name

Popular brands