Delta Elektronika SM120-25D Product Manual Download Page 3

SAFETY INSTRUCTIONS

SM3000

Page 2 - 2

DELTA ELEKTRONIKA B.V.

rev. February 2018

  Cau tion risk of elec tri cal Shock

!

  Instruction manual symbol. The unit will be marked with this symbol when it is

  necessary for the user to refer to the instruction manual

    Pro tec tive  ground  con duc tor  ter mi nal

o

   Off (sup ply)

I

  On (sup ply)

WEEE  (Waste Electrical & Electronic Equipment)

1

Correct Disposal of this Product

Applicable in the European Union.

This marking shown on the product, its packing or its literature indicates that

it should not be disposed with other wastes at the end of its working life, but

should be collected separately to recycle it responsibly to promote the

sustainable reuse of material resources.

11 Removal of (safety) covers  

Safety cover(s) are used to cover potentially hazardous voltages.

Observe the following when removing safety cover(s):

Switch off the unit.

Disconnect the unit from the mains supply or power outlet.

Wait for 5 minutes to allow internal capacitors to discharge.

Unscrew the screws and remove the cover(s).

Always place the cover(s) back before connecting the unit to the mains supply again.

12 Environmental Conditions

The Delta Elektronika power supplies safety approval applies to the following operating conditions:

Indoor use

Ambient temperature

20 to 50 

°

C

Maximum relative humidity

: 95%, non condensing, up to 40 

°

C

: 75%, non condensing, up to 50

 °

C

Altitude

: up to 2000 m

Pollution degree 

: 2

Summary of Contents for SM120-25D





















Reviews: