Delta Elektronika SM120-25D Product Manual Download Page 20

rev. February 2018

DELTA ELEKTRONIKA B.V.

Page 5 - 1

SM3000

EC DECLARATION

We

Delta Elektronika
Vissersdijk 4
4301 ND  ZIERIKZEE
The  Neth er lands

De clare  un der  sole  re spon si bil ity  that  the  fol low ing  Power  Sup plies:

SM

 

15-200 D

SM

 

30-100 D

SM

 

45-70 D

SM

 

70-45 D

SM

 

120-25 D

SM

 

300-10 D

Meet  the  in tent  of  Di rec tives  2014/30/EC  for  Elec tro mag netic  Com pat i bil ity  and
Di rec tives  2014/35/EC  re gard ing  Elec tri cal  Safety.  (Low  Volt age  Di rec tive)
Com pli ance  was  dem on strated  to  the  fol low ing  spec i fi ca tion  as  listed  in  the  of fi cial  Jour nal
of  the  Eu ro pean  Com mu ni ties:

EN 61000-6-3 Ge neric Emis sions: 

(res i den tial,  light  in dus trial)

EN 55022 Ra di ated and con ducted, Class 

B

EN 61000-3-3 Volt age fluc tu a tion and flicker

EN 61000-6-1 Ge neric Im mu nity: 

(res i den tial,  light  in dus trial)

EN 61000-6-2 Ge neric Im mu nity: 

(in dus trial  en vi ron ment)

EN 61000-4-2 Elec tro static Dis charge
EN  61000-4-3  Ra di ated  elec tro mag netic  fields
EN 61000-4-4 Elec tri cal Fast Tran sients / Bursts
EN 61000-4-5 Surge on DC out put
EN 61000-4-5 Surge on line in put
EN 61000-4-6 RF com mon mode, con ducted
EN 61000-4-11 Volt age vari a tions and dips

EN 60950 Safety of IT equip ment

EN 61010 Safety of elec tri cal equip ment for mea sure ment, con trol and lab o ra tory use

EC  Dec la ra tion  of  Con for mity  -  SM3000-series

Man ag ing  di rec tor
Zierikzee,  Feb ru ary  2018

DC POWER SUPPLIES

DELTA

 

ELEKTRONIKA B.V.

Vissersdijk 4, 4301 ND
Zierikzee, the Netherlands

www.DeltaPowerSupplies.com
Tel.  +31 111 413656

Summary of Contents for SM120-25D





















Reviews: