Delta Elektronika SM120-25D Product Manual Download Page 19

OPERATING - TROUBLE SHOOTING - CALIBRATING

SM3000

Page 4 - 8

DELTA ELEKTRONIKA B.V.

rev. February 2018

CALIBRATION

1)

GEN ERAL

The power sup plies are fac tory cal i brated
and nor mally need no fur ther cal i bra tion.

2)

METER  CAL I BRA TION

DIG I TAL  ME TERS
The zero in di ca tion can be cal i brated with
R712 and R716, the full scale in di ca tion can
be cal i brated with R706 and R708 on P388
(see fig. 4 - 19).

3)

SPE CIAL  CAL I BRA TIONS

The fol low ing cal i bra tions must be done by
qual i fied  per son nel  only.  Wrong  cal i bra tion
causes  mal func tion.  These  cal i bra tions  are
only needed af ter spe cial re pairs. 

Warn ing  !

Dam age caused by wrong cal i bra tion is not
war ranted.

CAL I BRATING  MAX.  CUR RENT  RANGE
or  CAL I BRATING  CC  MON I TOR  FULL

SCALE.
The max. out put cur rent can be cal i brated
with R686. R686 is lo cated on P432 (see
fig. 4 - 20).
Pro gram CC in put with ex actly 5.00 V. Set
out put volt age to a low value, en sur ing the
power sup ply is in CC mode. Mea sure the
out put cur rent with an ac cu rate shunt. Cal i -
brate the cur rent with R686 ex actly on the
rated max. cur rent.

Warn ing!

 Wrong cal 

bra 

tion can dam 

age

the unit.

CAL I BRATING  THE  CC  MON I TOR  OFF -
SET.
With R652 on P384 the off set of the CC mon -
i tor volt age can be cal i brated (see fig. 4 - 21). 
The unit has to be un loaded, the out put volt -
age set on a low value. Mea sure the off set
volt age of the CC mon i tor on the prog. con -
nec tor. Cal i brate the off set on a neg a tive
value be tween –10 mV and zero mV.

Warn ing!

 wrong cal i bra tion can dam age the 

unit.

4)

SPARE PARTS

When or 

der 

ing spare parts please state:

Model,  Se rial  num ber,  Com po nent  num ber
and  Com po nent  de scrip tion.

Ex am ple:

-

Model .............SM

 

30-100

 

D

-

Se rial  no. ........Sn821701900017

-

BSU no...........Bs816802900036

-

Com po nent.....D300

-

Description. ....BYV52-PI-200

fig.  4 - 19  Me ter cal i bra tion with 25-turn potmeters on P388

fig. 4 - 20 Cal i brating max. cur rent on P432                           

fig. 4 - 21  On P384, CC mon i tor can be cal i brated

Summary of Contents for SM120-25D





















Reviews: