Dell PowerEdge T100 Hardware Owner'S Manual Download Page 134

Page: 134 / 160

134

Running the System Diagnostics

•

Test Iterations

— Selects the number of times the test is run.

•

Log output file pathname

— When checked, enables you to specify where

the test log file is saved.

Viewing Information and Results

The tabs in the

Customize

window provide information about the test and

the test results. The following tabs are available:

•

Results

— Displays the test that ran and the result.

•

Errors

— Displays any errors that occurred during the test.

•

Help

— Displays information about the currently selected device,

component, or test.

•

Configuration

— Displays basic configuration information about the

currently selected device.

•

Parameters

— If applicable, displays parameters that you can set for the

test.

book.book Page 134 Wednesday, June 24, 2009 8:21 AM

Summary of Contents for PowerEdge T100

































































































































































Search results

Summary of Contents for PowerEdge T100

Reviews:

Related manuals for PowerEdge T100

Brands by name

Popular brands

Dell PowerEdge T100, Hardware Owner'S Manual

Search results

Summary of Contents for PowerEdge T100

Reviews:

Related manuals for PowerEdge T100

Brands by name

Popular brands