Dell PowerEdge T100 Hardware Owner'S Manual Download Page 69

Page: 69 / 160

Installing System Components

Figure 3-17.

Attaching a SAS or SATA Hard Drive to a SAS Controller Expansion Card

Ensure that all connectors are properly cabled and firmly seated.

Close the system. See "Closing the System" on page 47.

Reconnect the system to the electrical outlet, and turn on the system and
attached peripherals.

See the documentation that came with the drive for instructions on
installing any software required for drive operation.

power cable to hard drive (female)

power cable to hard drive (male)

SAS or SATA hard drives (2)

data cable to hard drive

data cable to SAS controller card

SAS controller card

book.book Page 69 Wednesday, June 24, 2009 8:21 AM

Summary of Contents for PowerEdge T100

































































































































































Search results

Summary of Contents for PowerEdge T100

Reviews:

Related manuals for PowerEdge T100

Brands by name

Popular brands

Dell PowerEdge T100, Hardware Owner'S Manual

Search results

Summary of Contents for PowerEdge T100

Reviews:

Related manuals for PowerEdge T100

Brands by name

Popular brands