Dell PowerEdge T100 Hardware Owner'S Manual Download Page 94 | Manualshive

Page: 94 / 160

background image

94

Installing System Components

Installing the Power Supply

1

Attach the cable clip to the new power supply.

2

Align the power supply mounting holes with the mounting holes on the
back panel.

3

Slide the power supply toward the back panel until it snaps into place over
the power-supply release tab.

4

Using a #2 Phillips screwdriver, install the four Phillips screws that secure
the power supply to the back panel.

5

Reattach the I/O panel and SATA cables (if present) to the routing clip on
the side of the power supply.

6

Depending on your system configuration, connect the following power
cables:

•

PWR_CONN connector on the system board

•

12V connector on the system board

•

Hard drives

•

Diskette drive

•

Tape backup unit

•

Optical drives

7

Close the system. See "Closing the System" on page 47.

Chassis Intrusion Switch

Removing the Chassis Intrusion Switch

CAUTION:

Many repairs may only be done by a certified service technician. You

should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.

1

Turn off the system and attached peripherals, and disconnect the system
from the electrical outlet.

2

Open the system. See "Opening the System" on page 47.

book.book Page 94 Wednesday, June 24, 2009 8:21 AM

«
...
92
93
94
95
96
...
»

Summary of Contents for PowerEdge T100

































































































































































Reviews:

No comments

Related manuals for PowerEdge T100

Brand: TANDBERG Pages: 127

Brand: PaloAlto Networks Pages: 30

FusionServer 5288 V6

Brand: xFusion Digital Technologies Pages: 131

Brand: Thecus Pages: 120

@server xSeries 343

Brand: IBM Pages: 193

301269U - Ethernet Disk Mini Home Edition 500 GB Network Attached Storage Hard...

Brand: LaCie Pages: 74

Brand: Waves Pages: 6

Brand: Arris Pages: 6

Brand: Muton Pages: 30

Brand: Brother Pages: 103

Brand: Generac Power Systems Pages: 52

Brand: Viavi Pages: 11

Brand: Axis Pages: 172

SuperStorageSystem SSG-2028R-DN2R40L

Brand: Supermicro Pages: 84

Brand: Eelectron Pages: 42

Brand: Eelectron Pages: 113

Brand: Optibase Pages: 28

AS2041M-32R Plus

Brand: Supero Pages: 106

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands