Dell PowerEdge T100 Hardware Owner'S Manual Download Page 97

Page: 97 / 160

Installing System Components

Figure 3-29.

Removing the Bezel

Replacing the Bezel

Align the bezel with the chassis frame and slide it into position.

Secure the alignment tabs into their alignment slots.

Attach the two bezel release screws to secure the bezel to the system
chassis. See Figure 3-29.

Replace the processor fan. See "Replacing the Cooling Fans" on page 87.

Reinstall the heat sink and shroud assembly. See "Replacing the Processor"
on page 83.

Close the system. See "Closing the System" on page 47.

Reconnect the system to the electrical outlet, and turn on the system.

alignment slot

bezel release screws (2)

bezel

alignment tab

book.book Page 97 Wednesday, June 24, 2009 8:21 AM

Summary of Contents for PowerEdge T100

































































































































































Search results

Summary of Contents for PowerEdge T100

Reviews:

Related manuals for PowerEdge T100

Brands by name

Popular brands

Dell PowerEdge T100, Hardware Owner'S Manual

Search results

Summary of Contents for PowerEdge T100

Reviews:

Related manuals for PowerEdge T100

Brands by name

Popular brands