Dell PowerEdge T100 Hardware Owner'S Manual Download Page 26

Page: 26 / 160

About Your System

Time-of-day clock

stopped

Faulty battery; faulty
system board.

See "Troubleshooting the
System Battery" on
page 114. If the problem
persists, see "Getting Help"
on page 141.

Time-of-day not set

- please run SETUP

program

Incorrect

Time

Date

settings; faulty system
battery.

Check the

Time

and

Date

settings. See "Using the
System Setup Program" on
page 29. If the problem
persists, see
"Troubleshooting the
System Battery" on
page 114.

Timer chip counter

2 failed

Faulty system board.

See "Getting Help" on
page 141.

Unexpected

interrupt in

protected mode

Faulty or improperly
installed memory modules
or faulty system board.

Ensure that all memory
modules are properly
installed. See "Memory
Module Installation
Guidelines" on page 76. If
the problem persists, see
"Troubleshooting System
Memory" on page 118. If
the problem persists, see
"Getting Help" on
page 141.

Utility partition

not available

Utility partition is not
available on the hard disk

Create a utility partition on
the boot hard drive. See the
CDs that came with your
system.

Warning! No micro

code update loaded

for processor 0

Micro code update failed.

Update the BIOS firmware.
See "Getting Help" on
page 141.

Table 1-6.

System Messages

(continued)

Message

Causes

Corrective Actions

book.book Page 26 Wednesday, June 24, 2009 8:21 AM

Summary of Contents for PowerEdge T100

































































































































































Search results

Summary of Contents for PowerEdge T100

Reviews:

Related manuals for PowerEdge T100

Brands by name

Popular brands

Dell PowerEdge T100, Hardware Owner'S Manual

Search results

Summary of Contents for PowerEdge T100

Reviews:

Related manuals for PowerEdge T100

Brands by name

Popular brands