Port Monitor Commands
653
31
Port Monitor Commands
PowerConnect switches allow the user to monitor traffic with an external
network analyzer. The external network analyzer can use any of the Ethernet
ports as a probe port. The probe port transmits a mirror copy of the traffic
being probed. Network traffic transmission is always disrupted whenever a
configuration change is made for port monitoring. Therefore, whenever port
monitoring is enabled, the probe port does not always forward traffic as a
normal port. When diagnosing problems, an operator should always check the
status of port monitoring.
The port monitoring feature allows the user to configure a single probe
session. A session consists of one destination port and multiple source ports.
When a session is enabled, any traffic entering or leaving the source ports of
that session is copied (mirrored) onto the corresponding destination port. A
network traffic analyzer can be attached to destination ports to analyze the
traffic patterns of source ports.
A session is operationally active only if both a destination port and at least
one source port are configured. If neither is true, the session is inactive. A port
configured as a destination port acts as a mirroring port when the session is
operationally active. If it is not, the port acts as a normal port and participates
in all normal operation with respect to transmitting traffic.
Any Ethernet port may be configured as a source port.
Caveats:
• Platforms may behave unpredictably if an attempt is made to mirror a port
of greater speed than the probe port.
• Once configured, there is no network connectivity on the probe port. The
probe port does not forward any traffic and does not receive any traffic.
The probe tool attached to the probe port is generally unable to ping the
networking device or ping through the networking device, and nobody is
able to ping the probe tool.
Commands in this Chapter
This chapter explains the following commands:
2CSPC4.X7000-SWUM204.book Page 653 Friday, March 15, 2013 8:22 AM
Summary of Contents for Networking 7048
