manualshive.com logo in svg

Dell Dimension 8400 Series, Manual

Share
Download
Dell Dimension 8400 Series Manual Download Page 92

92

Removing and Installing Parts

www

.dell.com | support.dell.com

Drives

Your computer supports a combination of these devices:

•

Up to two hard drives

•

One optional floppy drive

•

One optional Zip drive

•

Up to two CD or DVD drives

General Installation Guidelines

Connect serial ATA hard drives to the system board connectors labeled SATA-0, SATA-1, SATA-2, 
or SATA-3. Connect CD/DVD drives to the connector labeled PRI IDE.

When you connect two IDE devices to a single IDE interface cable and configure them for the 
cable select setting, the device attached to the last connector on the interface cable is the primary 
or the boot device (drive 0), and the device attached to the middle connector on the interface cable 
is the secondary device (drive 1). See the drive documentation in your upgrade kit for information 
on configuring devices for the cable select setting.

Connecting Drive Cables

When you install a drive, you connect two cables—a DC power cable and a data cable—to the back 
of the drive and to the system board. Some drives may also have an audio connector; one end of the 
audio cable attaches to the drive connector and the other end attaches to the system board.

Drive Interface Connectors

Serial ATA Connector

interface cable

interface connector

Summary of Contents for Dimension 8400 Series





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands