manualshive.com logo in svg

Dell Dimension 8400 Series, Manual

Share
Download
Dell Dimension 8400 Series Manual Download Page 11

Setting Up and Using Your Computer

11

Setting Up and Using Your Computer

Setting Up a Printer

 

NOTICE: 

Complete the operating system setup before you connect a printer to the computer.

See the documentation that came with the printer for setup information, including how to:

•

Obtain and install updated drivers.

•

Connect the printer to the computer.

•

Load paper and install the toner or ink cartridge.

•

Contact the printer manufacturer for technical assistance.

Printer Cable

Your printer connects to your computer with either a USB cable or a parallel cable. Your printer may 
not come with a printer cable, so if you purchase a cable separately, ensure that it is compatible 
with your printer. If you purchased a printer cable at the same time you purchased your computer, 
the cable may arrive in the computer box. 

Summary of Contents for Dimension 8400 Series





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands