manualshive.com logo in svg

Dell Dimension 8400 Series, Manual

Share
Download
Dell Dimension 8400 Series Manual Download Page 107

Removing and Installing Parts

107

6

Close the computer cover (see page 107).

 

NOTICE: 

To connect a network cable, first plug the cable into the network device and then plug it into 

the computer.

7

Connect your computer and devices to electrical outlets, and turn them on.

8

Enter system setup (see page 113) and restore the settings you recorded in step 1.

9

Properly dispose of the old battery. See the 

Product Information Guide

 for battery disposal 

information.

Closing the Computer Cover

 

CAUTION: 

Before you begin any of the procedures in this section, follow the safety instructions 

located in the 

Product Information Guide

.

1

Ensure that all cables are connected, and fold cables out of the way.

Gently pull the power cables toward you so that they do not get caught underneath the drives.

2

Ensure that no tools or extra parts are left inside the computer.

3

Close the cover:

a

Pivot the cover down.

b

Press down on the right side of the cover until it closes.

c

Press down on the left side of the cover until it closes.

d

Ensure that both sides of the cover are locked. If not, repeat all of step 3.

battery socket

battery

tab

Summary of Contents for Dimension 8400 Series





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands