manualshive.com logo in svg

Dell Dimension 8400 Series, Manual

Share
Download
Dell Dimension 8400 Series Manual Download Page 126

126

Appendix

www

.dell.com | support.dell.com

Argentina (Buenos Aires)

International Access Code: 

00

Country Code: 

54

City Code: 

11

Website: 

www.dell.com.ar

E-mail: [email protected]

E-mail for desktop and portable computers: 
[email protected] 

E-mail for servers and EMC:
[email protected]

Customer Care

 toll-free: 0-800-444-0730

Tech Support

toll-free: 0-800-444-0733

Tech Support Services

toll-free: 0-800-444-0724

Sales

0-810-444-3355

Aruba

General Support

toll-free: 800-1578

Australia (Sydney)

International Access Code: 

0011

Country Code: 

61

City Code: 

2

E-mail (Australia): [email protected]

E-mail (New Zealand): [email protected]

Home and Small Business

1-300-655-533

Government and Business

toll-free: 1-800-633-559

Preferred Accounts Division (PAD)

toll-free: 1-800-060-889

Customer Care

toll-free: 1-800-819-339

Technical Support (portables and desktops)

toll-free: 1-300-655-533

Technical Support (servers and workstations)

toll-free: 1-800-733-314

Corporate Sales

toll-free: 1-800-808-385

Transaction Sales

toll-free: 1-800-808-312

Fax

toll-free: 1-800-818-341

Austria (Vienna)

International Access Code: 

900

Country Code: 

43

City Code: 

1

Website: 

support.euro.dell.com

E-mail: [email protected]

Home/Small Business Sales

0820 240 530 00

Home/Small Business Fax

0820 240 530 49

Home/Small Business Customer Care

0820 240 530 14

Preferred Accounts/Corporate Customer Care

0820 240 530 16

Home/Small Business Technical Support

0820 240 530 14

Preferred Accounts/Corporate Technical Support

0660 8779

Switchboard

0820 240 530 00

Bahamas

General Support

toll-free: 1-866-278-6818

Country (City)
International Access Code 
Country Code
City Code

Department Name or Service Area,

Website and E-Mail Address

Area Codes,

Local Numbers, and

Toll-Free Numbers

Summary of Contents for Dimension 8400 Series





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands