Dell Alienware M14x R2 Owner'S Manual Download Page 9

Page: 9 / 104

Before You Begin

Before You Begin

Turn Off Your Computer and Connected Devices

CAUTION:

To avoid losing data, save and close all open files and exit all open

programs before you turn off your computer.

Save and close all open files and exit all open programs.

Click

Start

and click

Shut Down

Microsoft Windows shuts down and then the computer turns off.

NOTE:

If you are using a different operating system, see the documentation of

your operating system for shut-down instructions.

Disconnect your computer and all attached devices from their electrical

outlets.

Disconnect all telephone cables, network cables, and attached devices

from your computer.

After the computer is unplugged, press and hold the power button for

about 5 seconds to ground the system board.

Summary of Contents for Alienware M14x R2









































































































Search results

Summary of Contents for Alienware M14x R2

Reviews:

Related manuals for Alienware M14x R2

Brands by name

Popular brands

Dell Alienware M14x R2, Owner'S Manual

Search results

Summary of Contents for Alienware M14x R2

Reviews:

Related manuals for Alienware M14x R2

Brands by name

Popular brands