manualshive.com logo in svg

Dell EMC PowerEdge R7525, Installation And Service Manual, Page: 156 / 209

Share
Download
Dell EMC PowerEdge R7525 Installation And Service Manual Download Page 156

Installing the internal USB card

Prerequisites

1. Follow the safety guidelines listed in the 

Safety instructions

 on page 46.

2. Follow the procedure listed in 

Before working inside your system

 on page 47.

3.

Remove the expansion card risers

.

Steps

1. Connect the USB key to the internal USB card.

NOTE:

 Ensure to install the internal USB card in the IDSDM/USB card slot and not in the J_R3_PCIE_PWR

connector slot.

2. Align the internal USB card with the connector on the system board and press firmly until the internal USB card is seated.

Figure 116. Installing the internal USB card

Next steps

1.

Install the expansion card risers

.

2. Follow the procedure listed in 

After working inside your system

 on page 47.

3. While booting, press F2 to enter 

System Setup

 and verify that the system detects the USB memory key.

Intrusion switch module

Removing the intrusion switch module

Prerequisites

1. Follow the safety guidelines listed in the 

Safety instructions

 on page 46.

2. Follow the procedure listed in the 

Before working inside your system

 on page 47.

3.

Remove the expansion card riser

.

156

Installing and removing system components

Summary of Contents for PowerEdge R7525


















































































































































































































Reviews:

No comments