manualshive.com logo in svg

Dell EMC PowerEdge R7525, Installation And Service Manual, Page: 130 / 209

Share
Download
Dell EMC PowerEdge R7525 Installation And Service Manual Download Page 130

Next steps

1.

Replace the expansion card riser

.

Installing the expansion card risers

Prerequisites

1. Follow the safety guidelines listed in the 

Safety instructions

 on page 46.

2. Follow the procedure listed in 

Before working inside your system

 on page 47.

3. If removed, 

install the expansion cards into the expansion card risers

.

Steps

1. Holding the edges or the touch points, align the holes on the expansion card riser with the guides on the system board.
2. Lower the expansion card riser into place and press the touch points until the expansion card riser connector is fully seated on the

system board connector.

3. Tighten the captive screws on the risers and system if any.

NOTE:

 The numbers on the image do not depict the exact steps. The numbers are for representation of sequence.

Figure 83. Installing the expansion card riser (Riser 1)

130

Installing and removing system components

Summary of Contents for PowerEdge R7525


















































































































































































































Reviews:

No comments