Dell EMC PowerEdge R7525 Installation And Service Manual Download Page 185

Page: 185 / 209

Chassis dimensions

Figure 136. Chassis dimensions

Table 59. PowerEdge R7525

Drives

12 drives

482.0 mm

(18.97 inches)

434.0 mm

(17.08 inches)

86.8 mm

(3.41 inches)

With bezel:
35.84 mm (1.4
inches)

Without bezel:
22.0 mm (0.87
inches)

700.7 mm

(27.58 inches)

(Ear to rear wall)

736.29 mm

(28.98 inches)

(Ear to PSU
handle)

24 drives

482.0 mm

(18.97 inches)

434.0 mm

(17.08 inches)

86.8 mm

(3.41 inches)

With bezel:
35.84 mm (1.4
inches)

Without bezel:
22.0 mm (0.87
inches)

700.7 mm

(27.58 inches)

(Ear to rear wall)

736.29 mm

(28.98 inches)

(Ear to PSU
handle)

NOTE:

Zb is the nominal rear wall external surface where the system board I/O connectors reside.

Technical specifications

185

Summary of Contents for PowerEdge R7525


















































































































































































































Search results

Summary of Contents for PowerEdge R7525

Reviews:

Dell EMC PowerEdge R7525, Installation And Service Manual, Page: 185 / 209

Search results

Summary of Contents for PowerEdge R7525

Reviews: