Dell EMC PowerEdge R7525 Installation And Service Manual Download Page 65

Page: 65 / 209

Figure 35. Installing the cooling fan cage assembly

Next steps

1. If removed,

install the air shroud

2. Follow the procedure listed in

After working inside your system

on page 47.

Removing a cooling fan

Prerequisites

1. Follow the safety guidelines listed in the

Safety instructions

on page 46.

2. Follow the procedure listed in

Before working inside your system

on page 47.

3. If installed,

remove the air shroud

Steps

Press the orange release tab and lift the cooling fan to disconnect the fan from the connector on the system board.

NOTE:

The procedure to remove standard, high-performance, or very high-performance fan is same.

WARNING:

Ensure not to tilt or rotate the cooling fan while removing from the system.

Installing and removing system components

Summary of Contents for PowerEdge R7525


















































































































































































































Search results

Summary of Contents for PowerEdge R7525

Reviews:

Dell EMC PowerEdge R7525, Installation And Service Manual, Page: 65 / 209

Search results

Summary of Contents for PowerEdge R7525

Reviews: