manualshive.com logo in svg

Dell EMC PowerEdge R7525, Installation And Service Manual, Page: 86 / 209

Share
Download
Dell EMC PowerEdge R7525 Installation And Service Manual Download Page 86

Figure 64. Installing the front mounting front PERC module

Next steps

1. Reconnect all the required cables.
2. If removed, 

install the air shroud

.

3.

Install the drive backplane cover

.

4. Follow the procedure listed in 

After working inside your system

 on page 47.

Removing the rear mounting front PERC module

Prerequisites

1. Follow the safety guidelines listed in the 

Safety instructions

 on page 46.

2. Follow the procedure listed in the 

Before working inside your system

 on page 47.

3.

Remove the backplane cover

.

4. If installed, 

remove the air shroud

.

5.

Remove the drive backplane

.

6. Disconnect all the cables, observe the cable routing.

Steps

1. Using a Phillips #2 screwdriver, loosen the captive screws on the front PERC module.
2. Slide the front PERC module to disengage from the connector on the drive backplane.

86

Installing and removing system components

Summary of Contents for PowerEdge R7525


















































































































































































































Reviews:

No comments