manualshive.com logo in svg

Dell EMC PowerEdge R7525, Installation And Service Manual, Page: 56 / 209

Share
Download
Dell EMC PowerEdge R7525 Installation And Service Manual Download Page 56

Steps

1. Disconnect the control panel cable from the connector on the system board.
2. Using the Phillips #1 screwdriver, remove the screws that secure the left control panel and the left control panels cable cover to the

system.

3. Hold the left control panel cable, and slide the left control panel out of the system.

NOTE:

 Observe the routing of the cable as you remove the right control panel from the system.

NOTE:

 The numbers on the image do not depict the exact steps. The numbers are for representation of sequence.

Figure 26. Removing the left control panel

Next steps

1.

Replace the left control panel

.

Installing the left control panel

Prerequisites

1. Follow the safety guidelines listed in the 

Safety instructions

 on page 46.

2. Follow the procedure listed in 

Before working inside your system

 on page 47.

Steps

1. Align and slide the left control panel in the slot on the system.
2. Connect the left control panel cable to the connector on the system board .
3. Route the left control panel cable through the side wall of the system. Align and slide the left control panel cable cover in the slot on

the system.

56

Installing and removing system components

Summary of Contents for PowerEdge R7525


















































































































































































































Reviews:

No comments