manualshive.com logo in svg

Dell EMC PowerEdge R7525, Installation And Service Manual, Page: 127 / 209

Share
Download
Dell EMC PowerEdge R7525 Installation And Service Manual Download Page 127

Table 50. Config12-1: R1D+R2A+R3A+R4A(FL) (continued)

Agile Description

Supplier

Category

Card Priority

KIT,CRD,NVME,1.6,HHHL,PM17
25B

SAMSUNG

PCIE SSD

12200

KIT,CRD,NVME,3.2,HHHL,PM17
25B

SAMSUNG

PCIE SSD

12300

KIT,CRD,NVME,6.4,HHHL,PM17
25B

SAMSUNG

PCIE SSD

12400

KIT,CRD,NVME,1.6,HHHL,PM17
35

SAMSUNG

PCIE SSD

12500

KIT,CRD,NVME,1.6,HHHL,PM17
35,O

SAMSUNG

PCIE SSD

12600

KIT,CRD,NVME,3.2,HHHL,PM17
35

SAMSUNG

PCIE SSD

12700

KIT,CRD,NVME,3.2,HHHL,PM17
35,O

SAMSUNG

PCIE SSD

12800

KIT,CRD,NVME,6.4,HHHL,PM17
35

SAMSUNG

PCIE SSD

12900

KIT,CRD,NVME,6.4,HHHL,PM17
35,O

SAMSUNG

PCIE SSD

13000

KIT,CRD,NVME,750GB,HHHL,P
4800X

INTEL

PCIE SSD

13100

Removing the expansion card risers

Prerequisites

1. Follow the safety guidelines listed in the 

Safety instructions

 on page 46.

2. Follow the procedure listed in the 

Before working inside your system

 on page 47.

3. Disconnect any cables that are connected to the expansion card.

Steps

1. For Riser 1, loosen the captive screws on the riser.

a. Press the blue release tab and holding the edges lift the expansion card riser from the riser connector on the system board.

NOTE:

 The numbers on the image do not depict the exact steps. The numbers are for representation of

sequence.

Installing and removing system components

127

Summary of Contents for PowerEdge R7525


















































































































































































































Reviews:

No comments