background image

3

 

 

 

 

Dear Customer, 

We would like to thank you for choosing the high-quality DEFRO prod-

uct which will ensure your safety and operational reliability. 

As our customers, you can always count on help of the DEFRO Ser-

vice Centre, which is ready to ensure continuous efficiency of your stove. 

Please note that in order to use the dry stove safely and efficiently, it 

is crucial to get familiar with the following directions. 

 

Get familiar with this Operating Manual - useful remarks concern-
ing proper operation of the dry stove can be found there. 

 

Determine whether all parts have been delivered or the dry stove 

has not been damaged during transport. 

 

Check data on the rating plate against the warranty card. 

 

Prior to starting the dry stove, check flue connection against con-
nection recommendations included in this manual and appropri-

ate national regulations.  

Basic usage rules are to be obeyed while using the dry stove. Do not 

open the doors during operation of the device.  

DEFRO Service Centre or Authorized DEFRO Service should be al-

ways contacted when any intervention is necessary because only these 

parties have original spare parts and are properly trained within the scope 

of installation and operation of DEFRO boilers.  

For your safety and boiler use convenience please get acquainted with 

this operating manual and send back correctly filled copy of the Warranty 

Card to the following address: 

  DEFRO Sp. z o.o. Sp. k. - Centrum Serwi-

sowe 

Ruda Strawczy

ń

ska 103a 

26-067 Strawczyn 

 

fax 41 303 91 31 

@

  [email protected] 

By sending back your Warranty Card, you will be registered in our DE-

FRO heating boilers users database and we will be able to provide you 

quick and professional technical support.  

If you do not send back a correctly filled in Warranty Card and the dry 

stove quality and completeness receipt within the period of up to two weeks 

after the date of installation but no longer than within six months, after pur-

chasing, the 

warranty will become invalid.

 This results in delays with re-

pairs and the necessity of 

covering costs 

of service and travelling ex-

penses. 

Thank you for understanding. 

Yours sincerely,  

DEFRO Sp. z o.o. Sp. k. 

 

Content of this Operating Manual is a property of DEFRO sp. z o.o. Sp. k.. 

Any copying, duplicating, publishing of content of this Manual 

without prior written consent of DEFRO sp. z o.o. Sp. k. is forbidden. 

Dear Customer,

  

We would like to inform you that we make every efforts to offer 

products of quality fulfilling the most restrictive standards and warrant-

ing operational safety. All devices are produced in accordance with 

the requirements of relevant EU directives and have CE safety mark 

confirmed by the Declaration of Conformity EC. 

 

We appreciate all your comments and proposals regarding our 

level of service. We appreciate your comments and proposals regard-

ing our devices and the level of service provided by our Partners and 

Technical Support and Service. 

DEFRO Sp. z o.o. Sp. K. 

 

Summary of Contents for OMNIPELL

































Reviews: