background image

28

Davey

®

 Repair or Replacement Guarantee

In the unlikely event in Australia or New Zealand that this Davey product develops any malfunction within 
warranty periods beginning from the date of original purchase due to faulty materials or manufacture, Davey 
will at our option repair or replace it for you free of charge, subject to the conditions below.

Should you experience any difficulties with your Davey product, we suggest in the first instance that you 
contact the Davey Dealer from which you purchased the Davey product. Alternatively you can phone our 
Customer Service line on 1300 367 866 in Australia, or 0800 654 333 in New Zealand, or send a written 
letter to Davey at the address listed below. On receipt of your claim, Davey will seek to resolve your 
difficulties or, if the product is faulty or defective, advise you on how to have your Davey product repaired, 
obtain a replacement or a refund.

Your Davey Guarantee naturally does not cover normal wear or tear, replacement of product consumables 
(i.e. seals, bearings or capacitors), loss or damage resulting from misuse or negligent handling, improper 
use for which the product was not designed or advertised, failure to properly follow the provided installation 
and operating instructions, failure to carry out maintenance, corrosive or abrasive water or other liquid, 
lightning or high voltage spikes or unauthorized persons attempting repairs. Where applicable, your Davey 
product must only be connected to the voltage shown on the nameplate.

Your Davey Guarantee does not cover freight or any other costs incurred in making a claim. Please retain 
your receipt as proof of purchase; you MUST provide evidence of the date of original purchase when 
claiming under the Davey Guarantee.

Davey shall not be liable for any loss of profits or any consequential, indirect or special loss, damage or 
injury of any kind whatsoever arising directly or indirectly from Davey products. This limitation does not 
apply to any liability of Davey for failure to comply with a consumer guarantee applicable to your Davey 
product under the Australian or New Zealand legislation and does not affect any rights or remedies that may 
be available to you under the Australian or New Zealand Consumer Legislation.

In Australia, you are entitled to a replacement or refund for a major failure and for compensation for any 
other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if 
the goods fail to be of acceptable quality and the failure does not amount to a major failure.

Should your Davey product require repair or service after the guarantee period; contact your nearest Davey 
Dealer or phone the Davey Support Centre on the number listed below.

For a complete list of Davey Dealers visit our website (davey.com.au) or call:

*  Installation and operating instructions are included with the product when purchased new. 

They may also be found on our website.

AUSTRALIA
Davey Support Centre

6 Lakeview Drive,

Scoresby, Australia 3179

Ph: 

1300 232 839

Fax: 

1300 369 119

Website: davey.com.au

Davey Water Products Pty Ltd
Member of the GUD Group
ABN 18 066 327 517

NEW ZEALAND
Davey Support Centre

7 Rockridge Avenue,

Penrose, Auckland 1061

Ph: 

     0800 654 333

Fax:         09 527 7654

Website: daveynz.co.nz

™ Davey is a trademark of Davey Water Products Pty Ltd.
© Davey Water Products Pty Ltd 2014.

Davey Guarantee Period

Chlorination Cell – Three (3) Years or 10,000 operating hours 

(whichever comes first), 2 Years all other parts & 1 Year Labour

P/N 402147

Summary of Contents for ProMatic 24





























Reviews: