background image

18

FUNCTIONALITY OF YOUR CHLORINATOR (CONT)

SETTING THE CLOCK

Pressing the Clock button will allow you to set the real time clock. Press the up and down buttons to change 
the time by 1 minute. Holding either button down will change the time in 10 minute increments. The clock will 
begin to run when you exit this display.

You can switch between 12 & 24 hour time by pressing the up and down buttons simultaneously. The mode 
you select will be used wherever the time is indicated on the display.

SETTING THE TIMERS

Your chlorinator features two adjustable timers for automatic chlorination of your pool during the day. As the 
chlorinator cell can only operate while your filtration pump is running you need to ensure that the total daily 
run time will circulate all of the pool water volume through your filter at least once per day.

In addition to the filtration requirements the water temperature, numbers of bathers using the pool and 
amount of sunlight exposure can all affect the minimum daily run time. Please refer to the Chlorine 
Production section for more details.

Timer 1

Press 

Timer 1

 button once, Timer 1 Start will appear on the LCD display screen. This will default to 7am or 

(0700). Adjust operating time using the up & down arrows. Press 

Timer 1

 again, Timer 1 End will appear 

on the LCD display screen. This will default to 11am or (1100). Adjust operating time using the up & down 
arrows. To complete press any of the function buttons. 

Timer 2

Press 

Timer 2

 button once, Timer 2 Start will appear on the LCD display screen. This will default to 1pm or 

(1300). Adjust operating time using the up & down arrows. Press 

Timer 2

 again, Timer 2 End will appear on 

the LCD display screen. This will default to 5pm or (1700). Adjust operating time using the up & down arrows. 
To complete press any of the function buttons. 

Note: If you wish to turn Timer 2 ON or OFF, press the up 

& down arrows simultaniously to deactivate or activate the Timer 2 function.

Clock

12:30

aM

Clock

0:00

 

Timer 2 Start

1:00

pm

Timer 2 End

5:00

pm

Timer 1 Start

7.00

AM

Timer 1 End

11.00

AM

Summary of Contents for ProMatic 24





























Reviews: