Datakom DKG-519 User Manual Download Page 17 | Manualshive

Page: 17 / 55

background image

DKG-519 User Manual V-27

(14.04.2011)

- 17 -

6.8 Delayed Mains Simulation, Battery Charging

The Delayed Mains Simulation feature is used in battery backed up telecom systems where

batteries are able to supply the load during a certain period. The genset is requested to run only when
battery voltage drops below the critical level.

Once the engine runs, the rectifier system starts charging the batteries and the battery voltage

goes up immediately. Thus the engine should continue to run a programmed period for effective
charging.

The critical battery voltage level will be detected by an external unit which provides the digital

Simulate Mains signal for the genset control unit.

The unit offers an optional

SIMULATE MAINS

signal input. Any digital input may be assigned

as

Simulate Mains

using

Input Function Select

program parameters

.

It is also necessary to set the

ACTION

program parameter of the related input to

3

in order to

prevent any alarms generated from this input.

The SIMULATE MAINS signal may be a NO or NC contact, switching to either battery positive or

battery negative. These selections are made using the programming menu.

If the

Delayed Simulate Mains

program parameter is set to 1 and the input signal is active

when the genset is not feeding the load, then the genset will not run. This will prevent the genset from
starting when the simulate mains signal is present (batteries charged). The genset will start when the
simulate mains signal disappears.

If the genset is running when the signal is applied, then MAINS SIMULATION will be

prevented during

Flashing Relay Timer

program parameter. After this, usual Mains Waiting and

Cooldown cycles will be performed before engine stop. When the SIMULATE MAINS signal is present,
the front panels mimic diagram’s mains LEDs will reflect the mains voltages as present.

When the signal is passive, the unit will revert to normal operation and monitor the mains

voltage status.

The REMOTE START operation overrides DELAYED SIMULATE MAINS
operation. When both parameters “Remote Start Operation” and
“Delayed Simulate Mains” are set then REMOTE START operation mode
is performed.

«
...
15
16
17
18
19
...
»

Summary of Contents for DKG-519
























































Reviews:

No comments

Related manuals for DKG-519

SolarCell Remote

Brand: Samsung Pages: 2

Brand: Samsung Pages: 20

Brand: Omegalink Pages: 2

Brand: Rain Bird Pages: 138

Brand: Ziton Pages: 36

CPX-AP-A-16DI-D-M12-5P

Brand: Festo Pages: 16

Brand: ECKELMANN Pages: 147

Brand: Anritsu Pages: 54

Brand: Governors America Pages: 6

Brand: SKF Pages: 11

Brand: Quectel Pages: 97

Brand: Danfoss Pages: 162

Brand: Daikin Pages: 150

McDonnell & Miller PSE-80 Series

Brand: Xylem Pages: 8

Brand: Patton Pages: 56

Vision BT-A02 RF

Brand: Watts Pages: 19

Brand: H3C Pages: 15

Brand: Madas Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands