Datakom DKG-519 User Manual Download Page 41

Page: 41 / 55

DKG-519 User Manual V-27

(14.04.2011)

- 41 -

Program Group: Adjust Date and Time (password level-2)

Parameter Definition

Unit Factory

Set

Description

Date

01-31 Current day of the month.

Month

01-12 Current month.

Year

00-99 Last two digits of the current year.

Hours

00-23 Current hour of the day.

Minutes

00-59 Current minute of the hour.

Seconds

00-59 Current second of the minute.

Program Group: Weekly Schedule (password level-2)

Parameter Definition

Unit Factory

Set

Description

Monday Turn_on

24:00

Please review chapter 9 for a detailed description of
weekly programming schedule operation.

Monday Turn_off

24:00

Tuesday Turn_on

24:00

Tuesday Turn_off

24:00

Wednesday Turn_on

24:00

Wednesday Turn_off

24:00

Thursday Turn_on

24:00

Thursday Turn_off

24:00

Friday Turn_on

24:00

Friday Turn_off

24:00

Saturday Turn_on

24:00

Saturday Turn_off

24:00

Sunday Turn_on

24:00

Sunday Turn_off

24:00

Summary of Contents for DKG-519
























































Search results

Summary of Contents for DKG-519

Reviews:

Related manuals for DKG-519

Brands by name

Popular brands

Datakom DKG-519, User Manual

Search results

Summary of Contents for DKG-519

Reviews:

Related manuals for DKG-519

Brands by name

Popular brands