Daikin SUT10D80L21-10-F Operation Manual Download Page 53

Page: 53 / 61

PIM-00004

△

[Operation Manual]

53/61

DAIKIN INDUSTRIES, LTD.

<High-pressure Safety Valve Adjustment Procedure>

[1] Referring to the enlarged view of the high-pressure safety valve shown below, loosen the lock nut. (M10

lock nut, Width across flats: 14 mm)

[2] According to the pressure adjusting screw length reference chart, determine the screw length

corresponding to a desired control pressure setting.

* Tip of adjusting screw: Hexagon socket head, Width across flats: 5 mm

* One turn of the adjusting screw changes the pressure by approx. 7.7 MPa.

Lock nut tightening hole

Safety valve adjusting window

[3] Turn ON the hydraulic unit power supply, and select

the setting mode through panel key operation. Then,

set a desired pressure.

[4] Select [n05] (rpm display) in the monitor mode

through panel key operation to show the current rpm.

[5] Adjust the pressure adjusting screw length in the

longitudinal direction, and find an activation starting

point as shown on the right.

[6] Turn the pressure adjusting screw clockwise by 1/8

turn from the activation starting point to tighten the

screw.

Pressure adjusting screw length

[7] Tighten the lock nut. This completes the safety valve adjusting procedure.

(When tightening the lock nut, be careful not to allow the adjusting screw to turn.)

Pressure adjusting

screw length

Lock nut

Activation starting point

Cleaning door tight eni ng

prec aution nameplate

Safety precaution

nameplate

Unit nameplate

Summary of Contents for SUT10D80L21-10-F






























































Search results

Summary of Contents for SUT10D80L21-10-F

Reviews:

Related manuals for SUT10D80L21-10-F

Brands by name

Popular brands

Daikin SUT10D80L21-10-F, Operation Manual

Search results

Summary of Contents for SUT10D80L21-10-F

Reviews:

Related manuals for SUT10D80L21-10-F

Brands by name

Popular brands