Daikin SUT10D80L21-10-F Operation Manual Download

Page: 22 / 61

PIM-00004

△

[Operation Manual]

22/61

DAIKIN INDUSTRIES, LTD.

Connecting the I/O signal cable

(1) Connect the main power supply cable to the controller through the controller's wiring hole. Use a cable

clamp suitable for the wiring hole, which should provide IP54 or higher protection rating. (Wiring hole

diameter: 22 mm)

(2) Check the specifications of individual signal lines (see p. 24), and connect the cable to the I/O signal

terminal block.

DANGER

Do not connect the I/O signal cable to the power supply terminal block.

When unsheathing the cable, be careful not to damage the conductors.

Be careful that the cable conductors do not protrude from the terminal block.

CAUTION

After checking the specifications of individual signal lines (see p. 24), connect the cable to the I/O signal

terminal block.

The cable inserted into the cable clamp should be a multi-core cable as those recommended below.

If two or more cables are inserted into the clamp, the cable clamp does not conform to the specified

protection rating because of a gap between the cables and the cable clamp.

Terminate the shielded cable securely, and connect it to the shielded cable connection terminal.

If noise cannot be eliminated by connecting the shielded cable to the ground terminal, the user's

equipment should be directly grounded. (Disconnect the ground cable of this unit.)

I/O signal terminal block

Wiring hole

Shielded cable ground terminal

Connect a

ground c able to

the s peci fied

posi tion.

Ground

Summary of Contents for SUT10D80L21-10-F






























































Search results

Summary of Contents for SUT10D80L21-10-F

Reviews:

Related manuals for SUT10D80L21-10-F

Brands by name

Popular brands

Daikin SUT10D80L21-10-F, Operation Manual

Search results

Summary of Contents for SUT10D80L21-10-F

Reviews:

Related manuals for SUT10D80L21-10-F

Brands by name

Popular brands