Daikin SUT10D80L21-10-F Operation Manual Download Page 49

Page: 49 / 61

PIM-00004

△

[Operation Manual]

49/61

DAIKIN INDUSTRIES, LTD.

AC fan maintenance procedure

Removing the AC fan

Remove the full cover. (See p. 44)

Open the controller small cover, and remove the fan connector and the fan ground cable. (See p. 44)

Cut the binding strap that ties the fan harness.

Remove the hexagon socket head bolts with washers (M6 L15: two pieces), and remove the AC fan

bracket.

Cleaning the AC fan bracket

Remove the cross recessed head machine screws (M4 L70: two pieces), and separate the AC fan bracket form

the fan motor and the fan guard.

Cleaning the AC fan bracket

Blow steam or air onto the AC fan bracket to eliminate dust or contamination accumulated on/adhering to the

bracket.

Cleaning the AC fan

Clean the clearance between the blade periphery and the casing, as well as the fan blades and the casing, by

using a cloth.

CAUTION

[1] Prohibition of steam/air blow

Never attempt to blow steam or air onto the fan motor. Steam/air blow causes foreign bodies to be

blown into the motor.

Re-assembling the AC fan

After cleaning the AC fan, re-assemble it.

After reassembling is completed, make sure that the fan normally operates according to the test run procedure

described on p. 29.

(Check if the AC fan air intake/exhaust direction is correct. (See p. 15))

AC fan bracket

AC fan

Finger guard

Cross recessed head machine screw

Hexagon socket head bolt with washer

Summary of Contents for SUT10D80L21-10-F






























































Search results

Summary of Contents for SUT10D80L21-10-F

Reviews:

Related manuals for SUT10D80L21-10-F

Brands by name

Popular brands

Daikin SUT10D80L21-10-F, Operation Manual

Search results

Summary of Contents for SUT10D80L21-10-F

Reviews:

Related manuals for SUT10D80L21-10-F

Brands by name

Popular brands