Daikin SUT10D80L21-10-F Operation Manual Download Page 42

Page: 42 / 61

PIM-00004

△

[Operation Manual]

42/61

DAIKIN INDUSTRIES, LTD.

When the pressure switch display hold setting [P03] is "2", the alarm is stored in the alarm record if the

pressure falls below the value of the pressure switch setting [P01].

* The alarm/warning output of the individual alarm output of Classification [3], and the relay output B

contact of the integrated alarm output vary depending on the warning output level setting [P07].

See "Attachment: Power-ON External I/O Signal Timing Chart".

Causes of alarms and measures to be taken

Classification

Description

Indication

Cause of alarm output

Measure to be taken

Output device error

E10

The self-holding function of the power device
is activated.

If the event is repeated when the power supply is
reclosed, contact DAIKIN.

Instantaneous overcurrent

E11

The current control section senses
instantaneous overcurrent.

If the event is repeated when the power supply is
reclosed, contact DAIKIN.

Overspeed

E12

The motor runs at a speed faster than the
allowable speed (including reverse rotation).

Make sure that no problems exist in the hydraulic
circuit, and contact DAIKIN.

Regenerative brake
overcurrent

E13

Overcurrent is sensed in the regenerative
brake circuit.

If the event is repeated when the power supply is
reclosed, contact DAIKIN.

Regenerative brake overload

E14

Motor regenerative current causes the alarm
to be outputted when regeneration
overloading occurs.

Check the regenerative load integration ratio with
the monitor mode set at [n08], and alleviate the
load condition of the process in which the
integration ratio increases.

Undervoltage

E15

The main circuit voltage drops below 190
VDC (134 VAC).

Check the power supply voltage.
If the event is repeated, contact DAIKIN.

Overvoltage

E16

The main circuit voltage increases beyond
400 VDC.

Check the power supply voltage.
If the event is repeated, contact DAIKIN.

Motor Electronic thermal
error

E17

Overloading is detected via the status of the
current output. (60 seconds at 110%)

The motor output is larger than the normal output.
If the event is repeated, contact DAIKIN.

Magnetic pole detection error

E18

Faulty detection of the initial position of the
motor

If the event is repeated, contact DAIKIN.

Encoder cable break

E20

Alarm outputted as a result of a break in the
encoder

Parts should be replaced; contact DAIKIN.

Motor cable break

E21

Alarm outputted as a result of a break in the
motor

If the event is repeated, contact DAIKIN.

Power supply open phase

E24

Alarm outputted as a result of an open phase
in the power supply

If the event is repeated, contact DAIKIN.

Pressure sensor error

E30

Alarm outputted as a result of an abnormal
feedback value from the pressure sensor

If the event is repeated, contact DAIKIN.

Motor start error

E31

Alarm outputted when the command differs
from the actual rotation in polarity

If the event is repeated, contact DAIKIN.

Motor thermistor cable break

E40

Alarm outputted when a break in the motor
thermistor is detected

Parts should be replaced; contact DAIKIN.

Motor temperature abnormal
rise

E41

The motor is forcefully stopped when the
temperature reaches the specified temperature
(85 C) under the L44 condition.

The event can be caused as a result of a decrease in
the heat radiation and cooling performance of the
motor. Carry out servicing.

Radiator fin thermistor cable
break

E42

Alarm outputted when a break in the fin
thermistor is detected

Parts should be replaced; contact DAIKIN.

Fin temperature abnormal rise

E43

The motor is forcefully stopped when the
temperature reaches the specified temperature
(80 C) under the L45 condition.

The event can be caused as a result of a decrease in
the heat radiation and cooling performance of the
controller. Carry out servicing.

Drying operation error

E64

Alarm outputted when an increase in the
rotational speed is not accompanied by an
increase in pressure

The event can be caused as a result of a closed stop
valve or a decrease in the oil in the tank. Open the
stop valve and check the oil quantity.

[1]

CPU runaway (watchdog)

E91 Alarm outputted when the CPU runs away

If the event is repeated, contact DAIKIN.

Summary of Contents for SUT10D80L21-10-F






























































Search results

Summary of Contents for SUT10D80L21-10-F

Reviews:

Related manuals for SUT10D80L21-10-F

Brands by name

Popular brands

Daikin SUT10D80L21-10-F, Operation Manual

Search results

Summary of Contents for SUT10D80L21-10-F

Reviews:

Related manuals for SUT10D80L21-10-F

Brands by name

Popular brands