Daikin SUT10D80L21-10-F Operation Manual Download Page 50 | Manualshive

Page: 50 / 61

background image

PIM-00004

△

1

[Operation Manual]

50/61

DAIKIN INDUSTRIES, LTD.

Oil filling port (air breather) maintenance procedure

1. Removing procedure

The cap can be easily removed by turning it counterclockwise by

hand.

2. Cleaning procedure

Blow air onto the filter to blow off dust accumulated on/adhering to

the filter.

Remove dust from inside of the strainer cylinder.

<Oil filling port (Air breather)>

3. Mounting direction
Mount the cap by turning it clockwise by hand until it stops.

WARNING

During air blow, wear protective goggles to prevent accumulated substances or dust from touching your

eyes.

Suction strainer maintenance procedure

1. Removing procedure
[1] After draining hydraulic oil completely, remove

the nuts (M8: 12 pieces; Tightening torque: 9 to
10 N

m) from the cleaning door cover, and

remove the cover from the cleaning door.
* When the Super Unit uses the 160 L tank,

there are 14 nuts for the cleaning door.

[2] You can see the suction strainer. Loosen the

strainer, and remove it.
(Hexagon nut, Width across flats: 41 mm)

2.  Cleaning procedure
Blow air onto the filter to blow off dust accumulated
on/adhering to the filter.
Remove dust from inside of the strainer cylinder.

3.  Reassembling the strainer
After cleaning is completed, reassemble the suction
strainer. Follow the removing procedure in reverse.
After reassembling is completed, conduct the test run
procedure described on p. 29 to make sure that the
hydraulic unit normally operates.

WARNING

During air blow, wear protective goggles to prevent accumulated substances or dust from touching your

eyes.

Cap

Strainer

Cleaning door cover

Nut

Suction strainer

Cleaning door tightening

precaution nameplate

Safety precaution

nameplate

Unit nameplate

«
...
48
49
50
51
52
...
»

Summary of Contents for SUT10D80L21-10-F






























































Reviews:

No comments

Related manuals for SUT10D80L21-10-F

Brand: ABB Pages: 50

ACS880-01 Series

Brand: ABB Pages: 17

Brand: ABB Pages: 36

Brand: Parker Research Corp Pages: 3

Brand: S.I.T.A. Pages: 32

Brand: KaVo Pages: 13

Brand: vc999 Pages: 52

Brand: Eaton Pages: 2

Brand: Eaton Pages: 2

Brand: Eaton Pages: 20

Brand: Eaton Pages: 24

Brand: Water Witch Pages: 2

Brand: Falltech Pages: 48

Brand: Hantek Pages: 124

Brand: Hameg Pages: 10

Brand: Össur Pages: 50

Brand: Össur Pages: 13

PRO-FLEX XC PXC0xyyz

Brand: Össur Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands