![background image](http://html1.mh-extra.com/html/daikin/fxhq32aveb9/fxhq32aveb9_installation-manual_4704281013.webp)
English
12
(Abnormal heating may occur if the wirings are not tightened
securely.)
•
Use the required wirings, connect them securely and fix
these wirings so that external force may not apply to the ter-
minals.
•
Use a proper screw driver for tightening the terminal screws.
If an improper screw driver is used, it may damage the screw
head and a proper tightening cannot be carried out.
•
If a terminal is over tightened, it may be damaged. Refer to
the table shown below for tightening torque of terminals.
•
Conduct wiring so that the earth lead comes out from the
notched part of the cup washer. (Otherwise, earth lead con-
tact will be insufficient and grounding effect may be lost.)
•
Do not carry out soldering finish when stranded wirings are
used.
<Power supply wiring • earth wiring • remote controller wir-
ing • transmission wiring connecting method>
(1) Hold the control box, loosen the fixing screws (2 pieces)
and remove the control box lid
(Refer to Fig. 31)
.
(2) Open the knockout hole and put the resin bushing (10)
(accessory) on the rear or top side (sheet metal).
(3) Pull the power supply wiring through the penetration hole
and connect to the terminal block for power supply (X2M;
dipoles)
(Refer to Fig. 31)
. Connect the earth wiring to the
earth terminal. Next, tie into a bundle and fix by the
attached the wiring fixture (11) and clamp (4) so that no ten-
sion will be given to the wiring.
(Refer to Fig. 32)
(4) Pull the remote controller wiring and transmission wiring
through the penetration hole, and connect the remote con-
troller wiring to [P1·P2] and transmission wiring to [F1·F2]
(no polarity)
(Refer to Fig. 32)
. Next, tie into a bundle and
fix by the included the wiring fixture (11) and clamp (4) so
that no tension will be given to the wiring transmission part.
(Refer to Fig. 32)
WARNING
•
When wiring, form the wirings orderly so that the control
box lid can be securely fastened. If the control box lid is not
in place, the wirings may float up or be sandwiched by the
box and the lid and cause electric shocks or a fire.
Tightening torque
(N·m)
Terminal block for remote controller and trans-
mission wirings
0.88±0.08
Terminal block for power supply
1.47±0.14
Earth terminal
1.69±0.25
Connection of 2
wirings of same size
must be carried out
on both sides.
Connection of
wirings of different
sizes is prohibited.
Connection of 2
wirings on one side
is prohibited.
Notched part
Ring type crimp style terminal
Cup washer
L
N
Terminal block for remote
controller / transmission
wiring (X1M)
R10 or more
R10
or more
Remote controller wiring
(no polarity)
<Low voltage wiring connection method>
Printed Circuit Board
• Do not carry out
soldering finish.
• Do not carry out soldering finish.
Terminal block for power supply (X2M)
Earth terminal
Earth wiring
Power supply wiring
<High voltage wiring connection method>
Wiring penetration
hole
Rear piping
penetration cover
Remote controller
and transmission
wiring
Wiring diagram Label
Control box lid
Control box lid
fixing screws (2 pieces)
Power supply
wiring and earth wiring
Transmission wiring
(no polarity)
Control
box
Forbidden
Never connect the
power supply wiring.
(Refer to Fig. 32)
Fig. 31
01_EN_3P368557-2D.fm Page 12 Wednesday, February 13, 2019 2:46 PM