11
English
4. Clean the suction grille.
Wash the suction grille with water or neutral
detergent using a soft brush and then dry it.
When the suction grille is extremely contaminated
•
Spray the detergent for a ventilating fans and
ranges directly to the grille, and keep them under
that condition for about 10 minutes.
After that, carefully wash the suction grille with
water.
NOTE
•
Do not wash the suction grille with water of
50°C or higher.
It may cause discoloration and deformation.
•
When drying the suction grille, do not heat it
with fire. It may cause burning.
•
Do not use such as gasoline, benzine, thinner,
polishing powder and liquid insecticide sold
in the market.
It may cause discoloration and deformation.
5. Attach the air filter.
Refer to the Clause 4 for “
HOW TO CLEAN THE
AIR FILTER
”. (page 9)
6. Attach the suction grille.
Attach the grille in the reverse order mentioned
in the Clause 2.
7. Close the suction grille.
Slide all the knobs in the reverse order men-
tioned in the Clause 1 and securely fix them.
HOW TO CLEAN AIR OUTLET, OUTSIDE
PANEL, AND REMOTE CONTROLLER
•
Wipe them with a dry soft cloth.
•
When the stain cannot be wiped off, dip the cloth
in the neutral detergent diluted with water and
twist the cloth. After wiping off stain with this cloth,
wipe them with dry cloth.
NOTE
•
Do not use such as gasoline, benzine, thinner,
polishing powder and liquid insecticide sold
in the market.
It may cause discoloration and deformation.
•
Do not wash the filter with warm water of 50°C
or higher. It may cause discoloration and
deformation.
Detergent
CLEANING BEFORE AND AFTER SEA-
SONAL USE
STARTING AFTER LONG STOP PERIOD
Confirm the following
•
Check that the air inlet and outlet of indoor and
outdoor unit are not blocked.
Remove any obstacle.
Obstacles decrease the fan speed, and cause
performance decrease and breakage of the
devices.
Clean the air filter
•
After cleaning the air filter, make sure to attach it.
(Refer to “
8. MAINTENANCE
” on page 9.)
•
For information on how to install, remove, or clean
a optional sold air filter, refer to the user’s manual
attached to the air filter.
•
Turn off the indication “
” or “Time to clean fil-
ter” displayed on the remote controller after turn-
ing on the power.
The indication can be turned off whether in oper-
ation or at stop.
<In case of BRC1E>
•
For details, refer to the operation manual
attached to the remote controller.
Turn on the power circuit breaker at least 6
hours before operation.
•
This is required in order to activate the air condi-
tioner smoothly, and to protect air conditioner.
•
The display on the remote controller will be shown
when the power circuit breaker is turned on.
HEATING OPERATION within 6 hours after the
power is supplied to the air conditioner.
•
Some models perform the following operation to
protect the devices.
If the HEATING OPERATION is performed within
6 hours after the power is supplied to the air con-
ditioner, the indoor fan stops for about 10 minutes
during the outdoor unit operation to protect the
devices.
The above operation is performed not only at the
time of installation, but every time the power cir-
cuit breaker is turned off/on.
For comfortable use, do not turn off the power cir-
cuit breaker during seasonal use of the HEATING
OPERATION.
WHAT TO DO TO STOP THE AIR CONDI-
TIONER FOR A LONG PERIOD
Turn on FAN OPERATION for a half day on the
fine day and dry the indoor unit.
•
This can prevent the causes of mold.
4PEN465376-1.book Page 11 Wednesday, March 15, 2017 3:03 PM
