background image

5

English

(1)  Install the indoor unit temporarily.

• 

Fix the hanger bracket to the suspension bolt.

 

Make sure to securely fix the hanger bracket with the 

nut and the washer for hanger bracket (3) from the up-
per and lower side. 

(Refer to Fig. 7) 

If the washer fixing plate (7) is used,  the upper side 

washer for hanger bracket (3) may be protected from 
falling off.  
(Refer to Fig. 8)

[To fix hanger bracket]

Suspension bolt

Washer for hanger bracket (3) 
(Accessory)

Hanger bracket

Tighten the nut
(Double nut)

Nut 
(Field supply)

Fig. 7

[To fix washer fixing plate]

Washer fixing plate (7)
(Accessory) 

Upper side nut
(Field supply)

Insert

Fig. 8

(2)   

•  The installation pattern paper (5) is matched to the ceil-

ing opening dimension. 

For the height of ceiling lower surface from the floor 
level, confirm with the builder of ceiling.

•  The center of the ceiling opening is shown in the instal-

lation pattern paper (5).
The center of the indoor unit is indicated as triangle 
marks on the sides and bottom of the unit and those on 
the installation pattern paper (5).

•  Put the installation pattern paper (5) to the indoor unit 

with four screws (6).
At this time, put the installation pattern paper (5) to the 
indoor unit with the triangle marks on the indoor unit 
and those on the installation pattern paper (5) aligned.

Installation 

pattern 

paper (5)

(Accessory)

[Installation of the installation pattern paper]

Center of 

ceiling opening

Screw (6)
(Accessory)

Screw (6)
(Accessory)

Center of the 

indoor unit

Center mark 

of the unit

< Installation work after the ceiling work is finished >

(3)  Adjust the indoor unit to be located at the correct posi-

tion. 
(Refer to 

3. PREPARATION BEFORE INSTALLATION 

– (1))

•  Using the Installation guide (15) allows you to check 

the position from the underside of the unit to the lower 
ceiling surface.

Apply the short 
side of the 
cut-out section.

Lower ceiling 

surface

Installation guide (15)

(Accessory)

Underside 

of the unit

[For BYCQ54EEFU]

[For BYCQ54EEGFU]

Cut away the 1st and 2nd 
notches and apply.

Underside 

of the unit

Installation guide (15)

(Accessory)

(4)  Check the level of the unit. (Refer to Fig. 9)

(5) 

Remove the washer fixing plate (7) used for preventing 

the washer for hanger bracket (3) from dropping and 
tighten the upper side nut.

(6)  Remove the installation pattern paper (5).

Level

Vinyl tube

[Maintaining horizontality]

Fig. 9

01_EN_3P693452-2.indd   5

2022/08/09   16:00:11

Summary of Contents for FCQ18AAVJU





















Reviews: