manualshive.com logo in svg

Daikin DZK Series, Installation Manual

Share
Download
Daikin DZK Series Installation Manual Download Page 38

 

 

 

 

38 

 

Installation Manual 

Rev. 2.00  

Date 01-2019 

 

 

COMMUNICATIONS WITH THE INDOOR UNIT –  MODES / 
TEMPERATURE 

Check that the Navigation Remote Controller receives the operation 
mode change from the zoning system. To verify that, change the 
operation mode on the Main Wired Thermostat and verify that the 
new mode appears in the Navigation Remote Controller. 

 

DZK Wired Thermostat   

Daikin Navigation Remote Controller 

 

Check that the Daikin Navigation Remote Controller  receives the 
temperature changes from the zoning system. To do this, deactivate 
all thermostats but the Main Wired Thermostat. Change the Main 
Wired Thermostat  set point, and verify that the set point in the 
Daikin Navigation Remote Controller follows the specified set point 
changes. 

 

DZK Wired Thermostat   

Daikin Navigation Remote Controller 

 

 

Meaning

 

 

Ethernet connected 

Blinking 

Green 

 

Ethernet activity 

Blinking 

Yellow  

D7 

Data transmission from automation 

Blinking 

Red 

D8 

Data reception from automation bus 

Blinking 

Green 

D9 

Microswitch performance 

Blinking 

Green 

D10 

Connected to the Internet 

Blinking 

Green 

D11 

Network data transmission 

Blinking 

Red 

D12 

Network data reception 

Blinking 

Green 

D13 

Configured as IP address through DHCP 

On 

Red 

Configured as Fixed IP address  

Off 

Red 

D15 

Power supply  

Solid 

Red 

 

 

 

 

 

 

 

Summary of Contents for DZK Series

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands