manualshive.com logo in svg

Daikin DZK Series, Installation Manual

Share
Download
Daikin DZK Series Installation Manual Download Page 32

 

 

 

 

32 

 

Installation Manual 

Rev. 2.00  

Date 01-2019 

Zone Parameters 

Linked Zones. 

Displays the linked zones and allows you to select 

the secondary control dampers associated with the thermostat. 
 

Thermostat Type. 

Configure the thermostat as Main or Zone. 

 

Menu Mode. 

The thermostats can be set in Basic or Advanced mode 

(Advanced by default). When set to Basic mode, the user can control 
the following parameters: On/Off,  set  point, local ventilation and 
user settings. 
 

Offset. 

This option allows the user to apply an offset to the room 

temperature reading. The offset range goes from -5 to 5˚F (-2.5 to 
2.5˚C). The default value is 0˚F/ 0˚C. This offset will always be applied 
to the measured room temperature of the zone. 

 

User Mode Setpoint. 

This option is used to configure the set point 

temperature of each user mode for each zone. 

-

 

Comfort.

 Heating mode: 59 to 86˚F/ 15 to 30˚C, by default 

68˚F / 20˚C. Cooling mode: 64 to 86˚F/ 18 to 30˚C, by default 
75˚F / 24˚C. 

-

 

Eco.

 Heating mode: 59 to 86˚F / 15 to 30˚C, by default 66˚F / 

19˚C. Cooling mode: 64 to 86˚F / 18 to 30˚C, by default 84˚F / 
29˚C. 

-

 

Unoccupied.

  Heating mode: 59 to 72˚F/ 15 to 22˚C, by 

default 63˚F/17.5˚C. Cooling mode: 75 to 86˚F/ 24 to 30˚C, by 
default 81˚F/27˚C. 

-

 

Vacation.

 Heating mode: 50 to 61˚F/ 10 to 16˚C, by default 

50˚F/10˚C. Cooling mode: 84 to 96˚F/ 29 to 35.5˚C, by default 
95˚F/35˚C. 

 

Weight. 

This option  is used to  set the  weight of  each zone for 

purposes of determining system operation. The weight of the zone 
will be used for calculating the mode (auto-change over) or  for 
calculating heat demands when using  auxiliary heat. It is an 
indicator of the size / importance of the zone. Possible values range 
from 0-100. By default, the weighting is set to Auto and each zone's 
weight is automatically generated based on the number of zones. 
For example, if there are four zones, each zone's weight is 
automatically set to 25. 
If this option is disabled, the weight of the zone can be set manually.  

 

 

 

Note:

  it cannot be configured as 

Main  if there is already another 
Main thermostat. 

Summary of Contents for DZK Series

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands